Home | GPS | SUUNTO Watches | Special Offers | Deutsch
	Edge 500 | Edge 605 | Edge 705 | Forerunner 205 | Forerunner 305 | Forerunner 310XT | Forerunner 405 | Foretrex 301 | Foretrex 401 | Geko 201 | Geko 301 | eTrex H | eTrex Summit HC | eTrex Venture HC | eTrex Vista HCx | Dakota 10 | Dakota 20 | Oregon 200 | Oregon 450/450t | Oregon 550t | GPSMAP60Cx | GPSMAP60CSx | GPSMAP76C/x | GPSMAP76CS/x | Nüvi 550 | Nüvi 1490T | Nüvi 1690 | Nüvi 3790T | Nüvi 5000 | Nüvifone G60 | Zumo 220 | Zumo 660 | StreetPilot c3xx/c5xx | cfQue 1620 | GPS18 | TracPak | MapSource | Options | Buyer's Guide | Shopping basket

The following lists of changes are based on information provided by GARMIN. Changes or improvments which we consider important or especially useful are shown highlighted.

To view the current firmware version, complete the following steps:

1. Press the Page key until you see the Menu screen.
2. Select "Setup" and press the OK key.
3. Select "System" and press the OK key.
4. The current firmware version will be displayed near the bottom of the screen.
5. Press the page key to quit the screen.

Each upgrade replaces the complete firmware in the GPS, which means you need to install only the version you wish to apply. There is no need to install any previous versions.

Changes made from version 2.60 to 2.70: (released 05/03/2007)

1. Updated software to support manufacturing.

Not available for download.

To table of contents

Changes made from version 2.50 to 2.60: (released 02/09/2004)

1. Corrected potential shutdown when navigating a route with points sufficiently close to one another.

Firmware Upgrade V2.60 (Self-extracting ZIP-file, requires a PC and a connection cable, 656 kB)

To table of contents

Changes made from version 2.40 to 2.50: (released 11/07/2003)

1. Added Greek translations and Greek font.
2. Corrected compass display when navigating routes in areas with significant declination.

Firmware Upgrade V2.50 (Self-extracting ZIP-file, requires a PC and a connection cable, 716 kB)

To table of contents

Changes made from version 2.30 to 2.40: (released 10/03/2003)

1. Fixed potential memory corruption problem that could occur when tracking more than one WAAS satellite simultaneously.

Firmware Upgrade V2.40 (Self-extracting ZIP-file, requires a PC and a connection cable, 712 kB)

To table of contents

Changes made from version 2.20 to 2.30: (released 07/30/2003)

1. Updated French Translations.
2. Improved WAAS/EGNOS satellite selection algorithm to select the satellite with the most beneficial corrections given the unit's current position. A unit will not use a WAAS/EGNOS satellite if the unit's current position is outside of a given WAAS/EGNOS satellite's service volume.

Firmware Upgrade V2.30 (Self-extracting ZIP-file, requires a PC and a connection cable, 712 kB)

To table of contents

Changes made from version 2.10 to 2.20:

1. Added area and distance statistics for saved tracks. To view the statistics, select a saved track from the Track List Page, then select 'SHOW MAP' from the pop-up list. Area units are configurable. To configure, highlight the area units label, press OK, and select new units from the pop-up list.
2. Corrected problem that could potentially cause a saved track to include track segments not chosen or withhold track segments chosen during the track-saving process.

Firmware Upgrade V2.20 is not available for download.

To table of contents

TRAMsoft GmbH Laettenweg 19 / CH-8335 Hittnau / Switzerland Telephone: +41 44 995 1570 / Contact Last modification: 08/14/2010 (RA) (This document was created with TRAMsoft XbCMS V1.3-00, does not require any browser specific features and is compliant with the W3C standard "HTML 4.01 Transitional")